NEWSTips

10 Plumbing Tricks and Tips You Need to Know

You might want to contact one of our best plumbers in Sydney if you have a clogged pipe, a dripping faucet, or excessive water pressure. So, you should call your plumber.

DIY plumbing is rarely done by most homeowners due to lack of basic skills. Fixing plumbing issues on your own can worsen the situation for some homeowners.

Your damaged property will need costly repairs if you worsen an existing problem. Fortunately, there’s still something you can do to prevent having to call a plumber every time you encounter a plumbing issue.

The following are 10 plumbing tricks and tips you should know. You can save a lot of money by using these tips.

  1. Know where all the main valves are located

Know where the main valves are before settling in a new house. In the event of an emergency, such as a burst pipe, this will shut off the water supply.

Know where the main drain line is as well. Know where the access points to the sewer line are just in case you need to perform regular cleanings. Apartments and condos do not usually have their own valves, however.

  1. Know what is flushable and what is not

You should never use your toilet as a trash can. When you flush anything other than toilet paper and waste matter, you may cause serious toilet clogs. You can even clog your toilet with flushable wipes.

  1. Avoid dumping garbage in the drain

As a homeowner who values your home, you should never pour bacon grease, coffee grounds, vegetable peelings, food debris, coffee grounds, or even starchy foods like potatoes and rice down the drain.

Your drain will most likely be clogged by them. Go through your garbage disposal’s manual as well. By doing this, you’ll know what your garbage disposal is capable of and what it isn’t.

  1. Avoid puncturing your pipes

Before you pound nails or drill holes through the ceiling, floor, or wall, determine whether there is a drainage pipe or supply line behind it.

You don’t want to accidentally puncture the pipes. A stud finder can be used to locate pipes that may be hidden behind the walls.

It is inexpensive to buy a stud finder. Alternatively, you can use an endoscopic camera to locate pipes by snaking it through a wall.

  1. Make vacuuming your friend

When trying to remove clogs caused by small and hard objects, such as toys, combs, or toothbrushes, use a wet and dry vacuum to remove them.

Plunging only pushes objects deeper into a drainage, unlike vacuuming, which can dislodge small objects. It will become more difficult to remove an object if it is pushed further down the drainage.

  1. Plunging

Plunging is an effective method of clearing minor clogs in drains, sinks, and clogs. You can clean your sink traps by using a sink plunger to push water through them before detaching them. That way, the cleanout won’t be messy or wet.

  1. Make good use of plumber’s tape

Sealing pipe threads prevents water from leaking around fittings and joints. Plumber’s tape can easily be used to seal pipe threads. Teflon tape can also be used to seal pipes.

Before connecting plumbing fittings and joints, wrap the threads with the tape three times. Yellow tape is specially formulated for use in gas lines, while white plumber’s tape is suitable for general household plumbing.

  1. Always check your plumbing system for leaks

Checking for leaks will be helpful when doing a plumbing project. Let the water run through the pipes to do this. Turn the valves on and off. It won’t be hard to notice small leaks, just in case something is wrong. Make sure the leaks are sealed.

  1. Never ignore plumbing leaks

Your water bill can increase as a result of drips coming from your pipes or faucets. Dripping faucets waste several gallons of water each day.

Toilets can actually waste more than a hundred gallons a day. Whenever possible, repair water leaks. Any leak should never be ignored since it can turn into a larger, more expensive problem.

  1. Avoid over-tightening your plumbing fittings

When doing DIY plumbing projects, most homeowners overtighten their fittings and connections. This can lead to stripped screws and broken bolts. The best connections are hand-tight.

Related Articles

Leave a Reply

Your email address will not be published.

Back to top button
error: Content is protected !!